Closet shelves
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
OP
shareholder in the making
Joined: May 2003
Posts: 18,044 |
So the previous owner of this place (a flipper) installed crapass Closet Maid wire shelves in the closets. I've had two collapse now, so I've decided to replace them with simple 3/4" plywood shelves on top of 1x4 all around with metal supports in the middle and proper wooden hanger rods. Uuuuunfortunately, I've just run into a hitch. I have a rather iffy studfinder, but what I've discovered with it (and by putting a big enough hole into the drywall to shine a light in) is that the closet is built with metal studs. Any tips on how to deal with this? I have no desire to replace the studs in the closet, but I'm not sure what kind of screws to use to secure the 1x4s and supports or whether what I want to do is even feasible. For reference, I'm doing something like this. And yes, I've already bought the plywood and the lumber, although I haven't cut it to exact size yet.
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: Closet shelves
|
Joined: May 2002
Posts: 1,177
connoisseur
|
connoisseur
Joined: May 2002
Posts: 1,177 |
Hey Ken, forget about going into the steel studs and buy these.
Shawn
Epic 80/600 + M3's + M3 Algonquins + M2 Computer + EP125 I think I'm developing an addiction.
|
|
|
Re: Closet shelves
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
OP
shareholder in the making
Joined: May 2003
Posts: 18,044 |
What I've been seeing online (aside from the whole cut open your wall and put in wood thing) is toggle bolts into the metal studs.
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: Closet shelves
|
Joined: Feb 2004
Posts: 309
devotee
|
devotee
Joined: Feb 2004
Posts: 309 |
If you're not going to load them up with books or something else heavy, toggle bolts into the sheetrock will work. Drilling toggles into the metal studs will be a PITA. For clothes and the like, a toggle every 12" to 16" should be plenty.
I started out with nothing & I've still got most of it left M60 VP160 QS8 EP350 M22 VP100 Algonquins
|
|
|
Re: Closet shelves
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
OP
shareholder in the making
Joined: May 2003
Posts: 18,044 |
I would not be too terribly surprised if we put heavy things on the shelves. That's what we did before, after all. I figure I'll be buying myself some strength with the 1x4s, but I just wasn't sure whether to do toggle bolts into the studs or the sheetrock.
Then again, if it falls down, then I'll be able to practice drywalling and actually put up wood between the studs. Whee. Better the sheetrock rips out than the metal studs bend.
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: Closet shelves
|
Joined: Feb 2004
Posts: 309
devotee
|
devotee
Joined: Feb 2004
Posts: 309 |
Yep, metal studs without wood blocking are basically worthless for holding anything besides sheetrock.
A couple of other options that I've used are through-bolting to another 1x4 on the other side of the wall (depending on what's on the other side) or using vertical legs down to the floor. You might also try something wider than 1x4 so you could put 3-4 screws into each stud. Make sure to use screws specifically designed for metal studs (fine, not coarse, thread, and drill point).
I started out with nothing & I've still got most of it left M60 VP160 QS8 EP350 M22 VP100 Algonquins
|
|
|
Re: Closet shelves
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
OP
shareholder in the making
Joined: May 2003
Posts: 18,044 |
Heh. What's in the other side is the other closet. This could have potential! Do you put the bolt through drywall or through the studs?
Last edited by Ken.C; 10/07/12 03:07 AM.
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: Closet shelves
|
Joined: Feb 2004
Posts: 309
devotee
|
devotee
Joined: Feb 2004
Posts: 309 |
Back to back closets is ideal. You can have cleats for both closets at the same time. You can just bolt through the drywall, but try to stay close to the studs so you don't crack the drywall if you over-tighten the bolts. Don't ask me how I know this.
I started out with nothing & I've still got most of it left M60 VP160 QS8 EP350 M22 VP100 Algonquins
|
|
|
Re: Closet shelves
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
OP
shareholder in the making
Joined: May 2003
Posts: 18,044 |
Yeah, I kind of thought that was something of a danger.
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: Closet shelves
|
Joined: Dec 2007
Posts: 257
local
|
local
Joined: Dec 2007
Posts: 257 |
I have used these on a number of projects with great success. Most recently putting in a custom closet. This is a med size one. Into drywall, each one is good for 75 lbs. 4 of them? You are good to 300 lbs. http://www.homedepot.com/h_d1/N-5yc1v/R-...51#.UHHWla7DtM8
Last edited by mapatton; 10/07/12 07:28 PM.
Mark Pio 94,SB3,BD30,A35,Pio 48AV.Pronto 7000 controlling all. Getting ready for 22s, 150 & QS8s.
|
|
|
Forums16
Topics24,969
Posts442,619
Members15,632
|
Most Online2,699 Aug 8th, 2024
|
|
1 members (Hambrabi),
740
guests, and
2
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|